( This Post Contains Affiliate Links and We May Receive A Small Commission on Purchases)

Is Regrouting Worth It? Regrouting Complete Guide

So you are looking at that grouted tile in your house, and you are asking yourself how can you make this old floor look new again? Should you regrout or just change the floor tiles.

If you want to know if regrouting is worth it, the answer is regrouting is worth every time and investment you put into it. 

In this article, you will learn essential things you need to know about regrouting. That includes the cost of regrouting, tools you need, the regrouting process, and how long a regrout job lasts. 

 What Is a Grout?

Grout is a paste usually made with cement, water, and sand for filling especially the gaps between wall or floor tiles. After many years these fillings will start cracking causing the tiles to start lifting. 

These cracks can be repaired by the process of regrouting, that is removing the old grout carefully and filling it with a new one. In this detailed article I will be talking about if Regrouting is worth it, and step by step guide on how to regrout properly.

Should You Regrout Or Change The Floor Tiles?

Regrouting is much less expensive than replacing the floor tiles, but it does not last like a new replacement. But if you are on a low budget, regrouting the floor can be a pretty good option for you till you get enough money for a total replacement if the need be.

When Do You Need To Regrout Your Tile Grout?

 When you see loose tiles on the floor, it means that the grout holding the tiles is no longer effective, stains that are hard to remove, crack and such you need to consider regrouting.

How Much Does Regrouting Cost?

If you already have the tools and you are doing it yourself, then it won’t have to cost anything but a little cash to buy snacks when you are done.

But if you want to buy the tools or hire someone services to do it for you, then it gonna cost you as low as $100 or as high as $500 or more, that’s depending on how wide the area you want to grout is.

How Difficult Is Regrouting?

Regrouting may seem very difficult but it’s easy to do when you know the right steps to take. Even as a beginner if you follow the steps I will be listing below then you will be good to go.

Tools For Regrouting

Well like every other job that needs to be done, we will be needing the right tools for our regrouting job

  • · Powdered grout
  • · Drill/driver (cordless works best)
  • · Dust mask
  • · Rubber gloves
  • · Safety glasses
  • · Utility knife 
  • · Plastic scouring pad
  • · Grout sponge
  • · Stiff brush paint mixing paddle
  • · Grout saw
  • · Shop vacuum
  • · Carbide tip grout removal tool
  • · Bucket
  • · Grout float
  • · Tile sponge

Step One – Removing The Old Ground.

The first step to regrouting is to remove the old grout. Work patiently as this can be a tedious job, but it’s very necessary.

Make sure you are putting on a pair of rubber gloves, and safety glasses for protection, because as you dig out the old grout, it will cause dust to be flying around. 

 You might want to use a screwdriver in removing the old grout, but you are better off using a grout saw to avoid scratching the tiles.

 But if you don’t prefer doing it manually, you can an electric grout grinder, but be very careful when using it, so as not to damage the tiles. Carefully push the saw in between the tiles to remove the grout.

Step Two – Clean The Surface.

After you are fully done with removing the old grout, clean the surface very well with a vacuum cleaner, to remove any loose debris from the surface. Then use a cleaner to clean the tiles very well. 

Step Three – Mix The Grout

If you are not using a premixed grout, mix the grout you have purchased and ensure you follow the manufacturer’s instructions. It is recommended to use the grout modified with latex. This is better for bathrooms and wet areas because it is resistant to water.

When Regrouting does not mix grout that you will use more than 30mins, after a short while the grout thickens. To avoid this always mix grout you will use in a short while and when that one finishes, you can always mix a fresh one

When mixing the grout, do not use too much water. This will make the grout to be less thick and as such won’t hold the grout properly. It’s important to always wear a rubber glove to avoid chemical burns caused by the grout.

 Please note if you are Regrouting a small area choose the grout color that will match the old grout, or if it’s a large area the grout should be the same color as the tiles, this will the whole floor and even look.

Step Four – Apply The Grout

When applying the grout, use the float to spread it diagonally over the area. The float should be held at an angle of 30 degrees while you push the grout between the tiles.

 To full the joint, be sure to add extra grout into the joint until you are sure it is filled. Have in mind that you have to work quickly because the grout hardens in a short time, this is important.

Step Five – Remove Excess Grout

Remove excess grout from the floor with a float once every joint is filled. When removing, use the float at a sharp angle and move it diagonally across the tile floor to scrap the excess grout off.

When you are done with this step, allow the grout to set for 10 to 15 minutes or as recommended by the manufacturer.

Step Six – Clean The Tile Surface

Get a bucket with water inside, dip your tile sponge in water and wring out excess water from the sponge leaving it damp. In a diagonal motion use the damp sponge to remove excess grout from the surface.

Step Seven – Rinse And Repeat

Rinse the tile sponge and repeat the process in step seven. Eat time you do this make sure to wring the tile sponge very well to remove as much water as possible.

Allow the grout to set for about 24 hours or more before stepping on it. This is to make sure the grout is completely set and dry. 

Step Eight – Caulk The The Joints

This is done to fill up any gap in the joint. When the grout-caulk is applied use your finger to smooth.

Step Nine – Apply Final Grout Sealer.

 When you are all done, finally apply the grout sealer. This will prevent water from penetrating so much. This won’t make it waterproof it will keep it for years.

After applying the grout sealer, wipe out the tile surface to avoid the sealer staining the tiles.

How Long Does Regrouting Last? 

If properly done, regrouting should last about 10 to 15 years 

How Often Should You Regrout?

 Regrouting is not something you should do often, if you take care of your grout often you should be talking about 10 to 15 years. But if you do poor work, then we are talking about 8 to 10 years. 

To take care of the grout after regrouting always keep it clean to avoid the stains again. One way to do this is by washing it with baking soda and vinegar.

  •  Mix the baking soda with water and make a paste.
  • Using your finger apply the paste to the lines of the grout.
  • Mix the vinegar with water, pit in a bottle, and spray on the baking soda paste. Do not use vinegar if the floor is made with natural stones.  
  • Wait for few minutes to allow the bubbling action to stop. Then using a toothbrush scrub the grout lines carefully.
  • Then use plain water and the mob to clean off the mixed solution from the floor. When this is done, your floor should be sparkling.

For more ways to clean your grout, you can read more from wikiHow