( This Post Contains Affiliate Links and We May Receive A Small Commission on Purchases)

How to Remove Tile From Concrete Floor

Having a hard time with how to remove tile from the concrete floor? Then get settled because this article will guide you on all that you need to know. Getting new flooring or repairing a broken tile can be exhausting. But when the right procedures are followed, it will save you the stress and prevent you from destroying the subfloor.

Before the process takes place, you will need to remove things that are in your working space. Make the working space as free as possible to prevent things from damaging. If the room or area is set, then equip yourself. You need to cover your skin from scratch by wearing a long sleeve shirt. Switch off the water supply if you want to remove a sink or toilet. Cover irremovable things.

Protect your eye with eyewear or safety glasses. Your gloves too are necessary, knee pads, ear protection is a bonus. When tiles are broken, they tend to have sharp edges which can be dangerous to the skin or delicate places. Get your tools and get ready to start the process

How to remove tile from the concrete floor.

Start from Somewhere

It is recommended to start from a loose or broken tile. Loose tiles will be easier to start with because the adhesive has been made flexible. If there are no loose tiles, then use your hammer and chisel to break free from anywhere.

Remove a Tile

This is where you position your chisel into the seam at an angle and hit the back with your hammer to loosen the tile. It will pop right up and loosen an adjoining tile. If you are making use of a chipping hammer or an air chisel, then make use of the same procedure. If the tile is too stubborn, then try hitting harder. The stiffness of the tile depends on the type of adhesive that was used or how it was fixed.

When any tile is being removed, dispose of it in a bucket or trash can. This can help you create a working space and minimize litter. While doing so, keep in mind that it can be heavy to lift if filled to the brim.

READ  What To Do After Removing Popcorn Ceiling

Access Underlayment

This will help you know what you are dealing with. Most tiles are attached to the concrete floor or sub-floor directly when tiling is taking place. Some are also made with plywood or mortarboard which are most common. This should be an opportunity to remove any inappropriate or wrecked underlayment to make way for new flooring.

In a case whereby the underlayment is not damaged, it can be left to be reused.

Clean Debris

When the tiles are out, use a broom or a vacuum cleaner to remove all clouds of dust and specks of dirt from the concrete floor.

Eliminate Exposed Nails

If the underlayment were made do with, you would need to remove the nails or drive it in. This will help leave the floor on a flat surface.

Examine the Floor

When all the processes of removing tile have been carried out, then inspect the floor. Watch out for damages that might have occurred on the floor and repair it. Mend or replace any rotten wood. Your floor should be free from dirt and damages before another flooring is fixed.

Tile Removal Tools

There are a couple of tools for removing tiles from the concrete floor. They can come in power or hand tools. Each of the tools is to be used depending on the type of tile you are working on and how stiff it is. This list of tools is widely used.

They include Hammer; Screwdriver; Pry bar; Tarps and Plastic Wrap; Long-Handled Floor Scraper; Painters’ Tape; Shop Vacuum; Chisel or air Hammer with a Chisel set; Shovel and Buckets; Scraper.

How to Remove Tile Adhesive From Concrete Floor

Most times, to remove adhesive from concrete floors after the tile has been removed is hard. When removing a tile from a concrete floor or reusing an underlayment, it is crucial to know how to remove adhesives. This guide will help you remove it with ease but make sure the working space is well-ventilated or use a fan.

·   Use a citrus-based adhesive remover to cover the patches of the adhesive. You can get this remover from any store.

·   After waiting for the instructed time given by the manufacturer of the adhesive remover. Use the scraper on it. If a mortar was used on your tile, then use a chisel or hammer on it.

READ  How to Clean Unsealed Concrete floors

·   Dispose of the patches of the adhesive in a bucket.

·   Keep going through the process till all the adhesive is being removed.

How to Remove Vinyl Tile From Concrete Floor

Vinyl Tile is a flexible adhesive that develops more stringent over time. Vinyl tile adhesive can come up with ease. While trying to get it off, it can be hard or easy, depending on when it was applied. You can start scraping off with a chisel or putty knife.

If it seems too hard to come off, then apply heat to it. You can make use of a heat gun to get it off or carry an iron a few miles above the adhesive. Do not keep a hot object on the adhesive. After you have held a hot item near the glue, please wait a few minutes and then scrape it off. You can use an orange-based solvent instead of heat.

Using Solvent: Most times, using heat will not be enough to soften the vinyl adhesive. This depends on when the glue was applied. In this case, a solvent can serve. It can break down to bond to enable you to scrape it off. Buy a solvent that is compatible with the adhesive you want to remove.

Ventilate the working space before applying the solvent to the glue. It will break down the adhesive and enable you to break it down in an hour.

How to Remove Tile Mortar From Concrete Floor

This mortar is a Portland cement that is used on walls and floor tiles to stick it together. It tends to be unstable when it is dried, but it still maintains its durability, strong, and water-resistant features. It can come off with the tiles and leave small patches behind. To remove the small patches, use a chisel to avoid damaging the subfloor.

In a case, if large chunks, use a pry bar, exert pressure on the other end and pull up. You can use the chisel by hitting the edge with a hammer. The thin-set mortar will go off.

Can I Remove an Asbestos-Based Adhesive from a Concrete Floor

No, it is advisable to leave the removal of Asbestos to a professional. You should not be seen with asbestos. It is airborne and harmful to inhale. It can risk a person’s health and leave the person in a critical condition. Also, It is only a professional that knows how this adhesive works.

Removing tiles adhesive can be safe, but it is different when dealing with an asbestos adhesive. They are not dangerous when they are intact on the floor, but they are when they have been removed. This adhesive can be hazardous when it gets to the air as dust.

READ  Disadvantages of epoxy flooring

The safest way to glue is to put a new layer of flooring on it. You can as well seal it with a coat of epoxy concrete floor paint. These processes will keep the fibers of asbestos trapped on the floor.

Some adhesive turns out to contain asbestos in them. It will not be sure because it cannot be noticed by just looking at it. Most times, manufacturers indicate if it contains asbestos or not.

How to Remove Ceramic Tile from Concrete Floor without Breaking it

Ceramic floor tiles are standard and can be seen in rooms, kitchens, bathrooms, or sitting rooms. When it gets old, it can look worn, and the color can fade up. You can replace it if this happens with easy procedures that would not require breaking it.

There is a need for removing a ceramic tile without breaking it. It can be reused for coasters, tabletops, plant stands and other factors. Even if you will not need to reuse it, removing a ceramic tile without breaking it will make the whole process easy and less tiring.

When working on ceramic tiles, extra precautionary measures are taken. That is to protect you from getting hurt because a ceramic tile is a form of glass. It can be dangerous if it pierces any part of the body. There is a need for safety gloves, eye wears and a respiratory mask. The room you are working on should be closed to avoid spreading to other rooms.

How to Remove:

The first step is to remove your grouting. Make deep cuts along the grouting using a rotary cutter, or grout saw. Scrape off the grouting with a putty knife without damaging the surface of the tile. Mark an X of masking tape in the center of each tile. This will prevent it from cracking.

When the grout is gone, you can reach the edges of the tiles. Using a putty knife, place it on edge. Use your rubber mallet and gently rest the putty knife under the tile. This process should be repeated on the four sides of the tile. Lift the tile holding the four sides.

Continue the process to get it all out. Keep your removed tiles in a safe place.