Shark steam mop is one of the best steam mop manufacturers in the world. They are very effective at their work. But shark mop users share a common complaint, which is “shark steam mop not steaming.” This issue usually arises as a result of blockage and pressure leakage.
One common way to combat this problem is to pour vinegar in the tank and allow it to stay overnight. Another method to solve blockage is to utilize a descaling pin to remove the deposits of minerals in the machine. That aside, shark steam mop comes with other challenges, and this article will provide you effective solutions to fix them.
3 Effective Methods To Fix A Broken Shark Steam Mop
If you’re struggling to unclog or troubleshoot your shark steam mop, these three effective ways below can be used to fix it and get it working again
1. Manual Cleaning
There are three measures you must put in place before you begin to clean your steamer using the manual. Take note that these precautions are necessary. Hence it doesn’t matter whichever of the three methods you apply, just ensure to adhere to them.
- First of all, you must ensure the shark steam mop is not plugged in.
- The second precaution is for you to ensure that the steamer is completely cool. Therefore if you’ve just switched it off, be patient enough to allow it to cool down completely for some time.
- Lastly, endeavor to always disassemble the tank before having it emptied.
Once you have adhered to these measures, there are four items you need to have to unclog your steamer. They are as follows:
- Screwdriver (any model)
- Paper clips
- Cotton swab
2. Vinegar Cleaning Method
This is a method useful if you don’t want to get your hands dirty. While it’s the simplest, it’s still one of the best. However, before you learn how to do it, there is one thing you need to make sure of.
You’re required to use a 50% water – 50% vinegar solution in this procedure. Ensure that both the vinegar and water are in distilled form. The method may not be effective if they’re not. Follow the steps below to complete the process.
i. Ensure To Drain the Water Tank
There is no question that it’s required to drain the water tank, which contains any liquid.
ii. Prepare the solution.
Ensure the solution contains an equal amount of water and vinegar; as stated earlier, pour one constituent into another until the solution becomes homogeneous.
iii. Pour the solution into the water tank.
iv. Ensure Steamer is Plugged In
It’s recommended to plug the steamer in any area outside your sitting room or in the garage. It is not expected the steam will be used for will cleaning activities. Hence simply allow the steamer to run to vent out the steam. Once the water tank is drained, have it filled again, with only water for cleaning.
3. Commercial Cleaner Method
While the other methods are also effective, this has been widely tested and confirmed by the majority. Therefore you are most likely going to clean your steamer with this procedure. However, a commercially available cleaner is needed for this method. Follow the steps below to complete the process
i. Ensure to Empty the Water Tank
This is a similar step to the Vinegar Cleaning Method.
ii. Prepare a solution
It’s required you use a commercially available cleaner instead of vinegar in this step. Then make it a 50% water and 50% commercial cleaning agent. After that, pour it into the water tank.
However, you must pay attention to this essential thing. Ensure to allow the solution to sit idle for a long time to be homogenized. Only after when the components are homogenized can you proceed to the next step.
iii. Connect the steamer.
Lastly, make sure you have the steamer to run on its steam for cleaning purposes.
Tips Used To Avoid Clogs On Your Shark Steam Mop
i. Always Unclog Monthly
You have to maintain your steamer religiously to ensure it lasts a long time. It’s so easy to get your steamer unclogged monthly using the steps above. One thing you equally need to take seriously is to clean the steamer after each use. This ensures dust particles are removed.
ii. You should use distilled water.
It’s essential to use distilled water in your shark steam mop. This is the only way to prevent repair problems. But even at that, many people out there have never put distilled water into the tank of their shark steam mop. Distilled water will not lead to clogging up in your steamer. It is chemical-free, which means your steamer will last a long time.
Challenges Of Using Steam Mop
Below are some of the common problems mainly encountered when using steam mop:
i. Steam Mop Does Not Steam
Check if there’s water in the tank If the steam mop is not producing steam. If there’s no water, just remove the tank, then unscrew the cap and fill it. Once the tank is full, remove it and make sure the lid on the bottom of the tank is securely installed and tightened. You can unplug the device to try a different outlet to verify if the outlet works.
If the problem persists, switch on the device and press the trigger button for two minutes to start steaming. If steam is not generated, remove the tank, pour cold water into the hole where the filter connects to the device, and press the trigger to see if steam is generated. If so, a filter change is likely required. If the mop still doesn’t produce steam, the spray tips are probably clogged.
ii. Clogged Spray Tips
Steam mop spray tips can block the steam. To know if that’s the problem with your unit, switch off the mop and let it cool completely. Then turn the mop over and thoroughly inspect the spray tips for clogs. Depending on the manufacturer, this Sometimes involves removing a screw.
Also, you can use a small screwdriver or an opened paper clip to clean the spray tips. Gently insert the tool into the steam tip and gently rock it back and forth to remove any blockages. If your device still malfunction, simply contact the manufacturer.
iii. Excess Amount of Water on Floor
A steam mop functions more like iron as you release steam as you deem fit. When too much steam is given off, you will have a lot of water on the floor to deal with. Major problems with the microfiber cover can be another likely cause of excessive water.
You must switch off the steam mop and let it cool. After that, you should put the microfiber cover back on. Lastly, make sure you wait until the device is fully heated and ready before mopping the floor to prevent puddles.
iv. Steam Mop Leaks
If your steam mop leaks, make sure you find out if you have not overfilled the tank. If the tank continues to leak when the water level is lower, try to find out where the water is coming from. Get rid of the water tank to check if the filter, cap insert, and tank is damaged. If any of them is faulty, call the manufacturer and place an order for a replacement.
Also, check your warranty to see if your steam mop is protected against damage. If the container, filter, or steam cap insert is in good condition, simply reinsert the tank firmly to make sure it is pressed against the device.
Frequently Asked Questions
How do I clean my shark steam mop?
Here are tips to clean your shark steam mop:
- Clean or vacuum the floor to remove dry dirt and dust that can scratch the floor.
- Ensure to have your steam cleaner prepared.
- Endeavor you use water to fill the water tank.
- Turn on your steam mop and allow it to heat the water for 30 seconds.
Do steam mops sanitize?
Steam mop cleaning is not just a natural but also an effective way to remove stubborn dirt and stains when correctly used. The steam cleaner kills 99.9% of household microbes, like Staphylococcus, and even dust mites, bacteria and surface molds.
What can you put in my steam mop to smell nice?
Enumerated below are some of the best natural homemade scented solutions for a steam mop :
- Essential eucalyptus oil
- Lavender essential oil
- Other essential oils such as peppermint
Why is my steamer not steaming?
When your steamer gets clogged up with deposits of minerals, its production of steam will be affected. That’s to say it will stop generating steam. The good news is that you can decalcify the steamer. Do this by creating a solution that has equal amounts of both water and vinegar.
Finally, as long as you follow the above steps, your shark steam mop, not steaming, would cease to be a problem. If you owe a clogged shark steam mop, ensure to leave the unit unplugged. Plugging it is dangerous and can cause an explosion due to expansion from the heat produced.