( This Post Contains Affiliate Links and We May Receive A Small Commission on Purchases)

How To Transition Vinyl Plank Flooring From Room To Room

If you’re looking to learn how to transition vinyl plank flooring from room to room then this article is for you. Using different floor types for different rooms can be expensive. To save cost, it is advisable to maintain the same floor type for all rooms except when it is very necessary to alternate. 

Steps To Transition Vinyl Plank Flooring From Room To Room

To do this installation process nicely and avoid breaking up the vinyl plank, it is advisable to create continuity and a smoother effect. Since we are dealing with one type of flooring, it won’t be hard to get professional work done. But note that the more rooms, the more times you need a transition. To start this process, follow the steps below 

a. To begin, your vinyl plank flooring must be installed properly in every room because it will determine the transition of the flooring as you move further. 

b. The second step is to ensure that each room flooring installation you do must end underneath where the door is going to close to. The secret to this process is installing your flooring a little bit inside of the jamb and also right under just a little inside where the door stops. Make sure to leave a ¾ inch gap all through the way. 

c. The next step is to create your transition strip in a way that will cover the ¾ inch gap you made at the door. To do this, create the transition strips to be ¼ wide to give you the flexibility to cover the gap. Keep it where you want it and still have a lot of overlap on each side of the floor. Once this piece of transition strip is cut out then the next steps are easier to continue. The transition strip should be made with medium-density fiber fashioned tea molding.

d. Before you install the transition strips, you need to clean the hole in between the door where the transition strip goes in using a vacuum. 

e. Using a plastic piece that comes with the transition strips. Put it into the hole made, take a marker and indicate where the holes are in the track, and do the same to the underpad that is underneath and make it obvious.

f. The next step is to get some plastic plugs that you will need. This is because it is on top of concrete and if it were to be wood, then you will need just a wood screw to screw it down. Working with a concrete floor, you need to predrill the underpad and then put in a plug. Draw the holes marked on the underpad, put the plastic plugs in the hole made by the drill, and drive it in using a hammer.

g. Replace the plastic piece in the underpad and use another screw on each of the holes marked using a marker, drill it in and then slide in the transition strip and slowly snap it down. 

Do You Need Transition Strips With Vinyl Plank Flooring?

The only way you will not need transition strips is when you maintain the same direction throughout the house. If otherwise, then you need one for your vinyl plank flooring. The purpose of a transition strip is to provide a transition from one flooring surface to another. This can be as a result of height difference or just to make it look professional and neat. 

In any case where you are using the same flooring for your whole house, and you are not facing any height differences or underlayment problems, then you do not need transitions. 

The purpose of a transition strip can also be to provide a threshold from one room to another where the flooring is the same but a limit barrier is needed. This can be seen when you have the same flooring from the living room to the kitchen or dining room. To maintain a professional result, make a dry layout and trace where you need to make cuts.

What Are The Problems With Vinyl Plank Flooring?

Vinyl is a nice flooring type that looks attractive and beautiful but, it does not come without an issue. The good thing is that it is easy to notice these issues and tackle them when it arises. These problems and their solutions are:

a. Warping

This is a result of too much exposure to direct sunlight during installation. The effect causes the vinyl plank to expand. It can also be a result of water spillage on glue-down tiles or floors. To solve this, you need to ensure that proper care is taken during the installation process. Also, make sure you maintain your vinyl flooring following all basic maintenance procedures. 

b. Mold And Mildew

Mold and mildew can occur when there is high moisture or water leakage. To solve this, locate where the moisture is coming from and seal it with a moisture barrier. It can be hard to detect sometimes if the substrate is the source of the moisture. You cannot determine if the substrate is dry enough so you need to involve a flooring installation contractor. 

c. Peaking

This happens when two vinyl flooring squash against each other, causing it to lift at the joints. Vinyl flooring expands with time if no space is left for its expansion and contraction during installation and this can lead to peaking. To fix this, you need to trim the planks or tiles along the wall. Remove some of the molding to create space. You can also lay some heavyweight overnight on the lifted floor to flatten it. 

What Happens If You Don’t Acclimate Vinyl Plank Flooring?

When you do not acclimate your vinyl flooring, it can cause expansion or deformity. It can also lead to shrinkage or the development of gaps between the pieces. To be on the safer side, keep the room at a normal temperature for two days before you carry out any installation process. This will help the vinyl acclimate to the given temperature. For this to be possible, you should have your vinyl flooring delivered to you two days before the installation starts. 

What Not Use On Vinyl Plank Flooring?

While maintaining your vinyl plank flooring, there are things to avoid because they can cause harm to your flooring. Once you can adhere to these, it will increase the durability of your vinyl plank flooring. They include: 

a. If you are vacuuming your vinyl flooring, avoid using a beater bar attachment because it can harm your flooring surface.  

b. Make sure to use felt pads to keep your furniture to avoid scratches if they are moved across the floor.

c. Avoid ammonia or ammonia-based cleaning products on your vinyl floor to protect it from breaking down the material and causing cracks.

d. Using abrasive cleaners or detergents can dull film your vinyl plank flooring. 

Conclusion

A perfect transition makes the flooring look presentable that one can hardly notice that something like that went on. When extra care is taken, you would be left with a shiny vinyl plank flooring. Thus, projects that have to do with the transition on any type of flooring should be done professionally. This is to ensure a perfect result and to increase the durability of your floor.